Do not use a Read all safety warnings, instructions, power tool while you are tired or under the influence illustrations and specifications provided with of drugs, alcohol or medication.
Wait for all moving parts to stop and than the table top. Serious injury could occur if the tool a hazard. Should this ever occur, stand clear and allow is tipped or if the cutting tool is unintentionally contacted. Arbor Hole Cutting Capacity for No Load Speed Before use of this product, familiarize yourself with all operating features and safety rules.
Push the lever down to lock the saw in place. To release the saw, lift the miter lock lever and depress the detent release button. A dust bag is provided for use on the miter saw.
It fits over the exhaust port on the upper blade guard. To install it, squeeze the two metal clips to open the mouth of the bag and slide it on the exhaust port. Never use a blade that is too thick to allow outer blade washer to engage with the flats on the spindle. Make sure the spindle lock button is not engaged To unlock and raise the saw arm: before reconnecting saw into power source.
See figure Recheck blade-to-table alignment. See Figures 22 - Staring into the light beam may result in serious injury or vision loss. The LED lighting system casts the shadow of the blade onto the workpiece.
Depress the trigger lockout lever and squeeze the switch trigger. Allow several seconds for the blade to reach maximum speed. A compound miter cut is a cut made using a miter angle and a bevel angle at the same time. This type of cut is used to make picture frames, cut molding, make boxes with sloping sides, and for certain roof framing cuts.
Since compound cuts are the most difficult to accurately obtain, trial cuts should be made in scrap material, and much thought and planning made, prior to making your required cut. The bevel stop turret can be used to Your compound miter saw does an excellent job of cutting set the bevel angle to The miter angle should be set crown molding.
When cutting warped material, always make sure it is To avoid a kickback and to avoid serious personal positioned on the miter table with the convex side against injury, never position the concave edge of bowed the fence as shown in figure Before performing any adjustment, make sure the tool is unplugged from the power supply.
NOTE: These adjustments were made at the factory and normally do not require readjustment. If the miter lock lever feels loose or the table moves easily when in the locked position, an adjustment to the miter lock lever is required. The saw has externally accessible brush assemblies that When servicing, use only identical replacement should be periodically checked for wear. Use of any other part can create a hazard or cause product damage.
Over time the LED light may become cloudy or dull. If this occurs, the LED lens may require cleaning. Abaisser le levier pour verrouiller la scie en place. To reduce the risk of injury, the user must read and understand the operator's manual before using this product. Previous Page. Next Page. Saw Ridgid R Operator's Manual 10 in. Learn the applications and limitations as well as the specific potential hazards related to this tool.
Page 4: Specific Safety Rules If a work clamp and length stop are used together, they must both be installed on the same side of the saw table to prevent the saw from catching the loose end and kicking up. Please study them and learn their meaning. Proper interpretation of these symbols will allow you to operate the tool better and safer. All exposed metal parts are isolated from the internal metal motor components with protect- ing insulation.
Double insulated tools do not need to be grounded. Page 9: Glossary Of Terms The area over, under, behind, or in front of the blade. As it applies to the workpiece, that area which will be or has been cut by the blade. The distance that the tip of the saw blade tooth is bent or set outward from the face of the blade.
Snipe planers Depression made at either end of a workpiece by cutter blades when the workpiece is not properly supported. Arbor Hole No Load Speed RPM Input Page Electric Brake 12 IN.
It retracts over the upper blade guard as the saw is lowered into the workpiece. Page Assembly This product requires assembly. NOTE: This tool is heavy. To avoid back injury, lift with your legs, not your back, and get help when needed.
A dust bag is provided for use on your miter saw. It fits over a dust guide or exhaust port. Then, squeeze the two metal clips to open the mouth of the bag and slide it on the exhaust port. Never use a blade that is too thick to allow outer blade washer to engage with the flats on the spindle. Larger blades will come in contact with the blade guards, while thicker blades will prevent the hex bolt from securing the blade on the spindle.
Prior to squaring the saw blade to the fence, check the miter lock lever for proper adjustment. Rotate the miter table and set the saw at 0 miter. Page 24 Use the work clamp or a C-clamp to secure the workpiece when possible. Page 26 Use the work clamp or a C-clamp to secure the workpiece when possible.
0コメント